Hospital Capper Sealing Machine with CE from China manufacturer - Ningbo Joident Electronics Technology Co.,Ltd

Price:	1.0~500.0 USD
Payment Terms:	T/T,L/C,WU
Place of Origin:	Zhejiang, China (Mainland)


	Add to My Favorites
HiSupplier Escrow	Share \|

Product Detail

Model No.: Solo

Production Capacity: 1000pcs/month

Delivery Date: 15 working days

Automatic Grade: Semiautomatic

Usage: Outer

Brand Name: JOIDENT

Seal length: 300mm

Preheating: 2-3 minutes

Gross weight: 7.5kg

Certificate: CE

Means of Transport: Ocean,Air

Packing: Carton

Processing: Sealing Machine

Type: General

Packaging: Paper

Seal width: 12mm

Voltage: AC 110/220V 50/60Hz

Power output: 100W

Packing size: 460x360x170mm

*Power:100W
*Voltage:AC 110V/220V, 50/60HZ
*Type of sealing: At constant temperature

30cm Seal Length Surgical Sterilization Sealing Facility/Hospital Capper Sealing Machine with CE

1-Main Features

*According to European standard sealing.

*PC board with automatic temperature control.

*Short pre-heating time:2 minutes.

*Energy saving design, Beep-alert, Intergrated cutting.
30cm Seal Length Surgical Sterilization Sealing Facility

a. Roll-holder tube b. Roll-holder c. Cutting blade runner d. Indicator

e. Sealer arm f. Socket for power cord g. Power switch

Technical data:

Power input	AC110V/230V 50/60Hz
Pre-heating	2~3minutes
Power	100W
Isolation	I/IPX0
Type of sealing	At constant temperature
Sealing length	30cm
Sealing width	12mm
Gross weight	7.5kgs
Package Dimensions (WxLxH)	460360170mm
Environmental temperature	+5 / +40 °C
Relative max. humidity	85%
Max voltage variation	± 10 %
Pollution level	1

2-Instructions for Use:

Before using:

a. Position the Sealer on a flat surface with sufficient working space around it.

b. Do not install the machine next to sinks or anything similar in order to avoid contact with water and the short circuit of the electrical system.

c. Avoid proximity to sources of heat.

d. Install the machine in an area with normal ventilation.

e. Make sure that the power cord is not bent and that it is free of obstruction up to the electric socket.

3-Installation:

a. Remove the sealing/cutting station and the roll-holder with care from the packaging.

b. Insert the roll-holder into the sealing & cutting station, Tighten the three screws with the key until they are fully tightened.

c. Insert roller-holder tubes on the roll-holder, if necessary by turning the tube.

4-Operation:

(a) Connect the power cord to the power connector which is on the back side of the sealer, check if the voltage of your equipment matches the voltage of the local electrical network.

(b) Switch the sealer on by using the power switch on its back side and adjust the sealing temperature through the temperature selector on its right side according to the thickness of the material to be sealed. When the green LED goes off (after around 2 minutes) the sealer will be ready to be used.

(c)Place the roll on the holder. The beginning of the roll shall be inserted through the back side, between the pressure bar and the sealing bar always with the paper side down (resistance's side)and the plastic side up (directly under the upper pressure bar). Pull the sealer arm towards the operator and press it down softly until it is locked. Exaggerated pressure may break the sealer arm and this kind of damage is not covered by the warranty. The sealing time (around 4seconds) must be manually controlled by the user. Note: If the sealing temperature is too low or too high the sealing might be inefficient (the envelopes may be stuck to the sealing area when they are pulled or be visibly badly-sealed). To correct this, adjust the timer properly. Once adjusted it is not necessary to perform any other adjustment to continue sealing.

(d) To cut the packages, still with the arm locked, slide the blade from one side to the other, raise the sealer arm and remove the envelopes.Note: If the blade knob is pulled slowly the paper may crease and the cutting will not be adequate. To make it more precise, pull the blade knob quickly. If necessary, slide the cutting blade more than once.

3-Payment details
T/T, L/C & west union acceptable.

4-Shipment

Express: 1 or 2pcs samples testing, express recommended.e.g: TNT,DHL,UPS etc. Shipping days 3-5days.
Air shipment: Between 3pcs and 5pcs, normal air shipment recommended. Shipping days 5-10days.
Sea shipment: More than 6pcs, normal sea shipment recommended. Shipping days around 30days.